Microcontroller based anaesthetia inject indicator

If the operation lasts for a long time, say for suppose for 4 or 5 hours, complete dose of anesthesia cannot be administered in a single stroke. It may lead to the patients death. If lower amount of anesthesia is administered, the patient may wakeup at the middle of the operation. To avoid this, the anesthetist administers few milliliters of anesthesia per hour to the patient.

Microcontroller based anaesthetia inject indicator

If the operation lasts for a long time, say for suppose for 4 or 5 hours, complete dose of anesthesia cannot be administered in a single stroke.

PowerPoint Slideshow about 'MICROCONTROLLER BASED ANESTHESIA INJECTOR' - jayme

If lower amount of anesthesia is administered, the patient may wakeup at the middle of the operation. To avoid this, the anesthetist administers few milliliters of anesthesia per hour to the patient.

If the anesthetist fails to administer the anesthesia to the patient at the particular time interval, other allied problems may arise. To overcome such hazardous problems the design of an automatic operation of an anesthesia machine based on a micro-controller is effective.

In this system a keypad is provided along with the microcontroller and syringe infusion pump. The anesthetist can set the level of anesthesia in terms of milliliters per hour to administer anesthesia to the patient with the help of keypad. After receiving the signal from the keypad, the microcontroller controls the signal to the desire level and fed into the stepper motor to drive the infusion pump in proper manner.

The anesthesia is administered to the patient according to the stepper motor rotation the syringe will move forward or backward direction. This particular paper will be very much useful to physicians to see the current position of anesthesia of the patients.

If the level of anesthesia is decreased to lower level set valuethe alarm will be initiated to alert the physician to refill the anesthesia in the Syringe Pump to continue the process.

An example is the microwave oven. It is hardly realized that the oven actually consists of a processor and the software running inside. Another example is the TV remote control.

Very few actually realize that there is a microcontroller inside that runs a set of programs especially for the TV. Automatic Anesthesia Injector system is also an application of embedded technologies in which a microcontroller is used to control the entire device.

The prime use of a microcontroller is to control the operation of a machine using a fixed program that is stored in ROM and that does not change over the lifetime of the system.

A microcontroller is a highly integrated chip that includes all or most of the parts needed for a controller in a single chip. The microcontroller could be rightly called a one-chip solution. But, the micro controller has got all these peripheral facilities on a single chip and hence development of similar system with micro controller reduces PCB size and the overall cost of the design.

Microcontroller based anaesthetia inject indicator

The difference between a Microprocessor and Microcontroller is that a Microprocessor can only process with the data, but Microcontroller can control external device in addition to processing the data. But with Microcontroller the device can be directly controlled without an IC.

A Microcontroller often deals with bits, not bytes as in the real world application, for example switch contracts can be open or close, indicators should be lit or dark and motors can be either turned on or off and so forth.

Microcontroller Based Anesthesia Injector project | Engr Rana M Shakeel - benjaminpohle.com

These operations will lead to blood loss and pain. Therefore it is necessary to arrest the pain and the blood loss. Anesthesia plays an important role in the part of painkilling.

AAI can be defined as Automatic administration of anesthesia based on the bio-medical parameters of the patient, eliminating future side effects and the need for an anesthetist.

Anesthesia is very essential in performing painless surgery and so an Automatic administration of Anesthesia is needed for a successful surgery. In this design, a micro-controller is used for controlling the anesthesia machine automatically, depending upon the various biomedical parameters such as body temperature, heart rate, respiration rate etc.

Major operations are performed to remove or reconstruct the infected parts in the human body. These operations lead to blood loss and pain.

MICROCONTROLLER BASED ANESTHESIA INJECTOR - Download as Word Doc .doc), PDF File .pdf), Text File .txt) or read online. MICROCONTROLLER BASED ANESTHESIA INJECTOR ABSTRACT In the hospitals when any major operation is performed, the patient must be in anesthetize condition. If the operation lasts for a long time, say for suppose for 4 or 5 hours, complete dose of anesthesia cannot be administered in a single stroke. It may lead to the patient’s death. Microcontroller Based Anesthesia Injector full report,Ask Latest information,Abstract,Report,Presentation (pdf,doc,ppt),Microcontroller Based Anesthesia Injector full report technology discussion,Microcontroller Based Anesthesia Injector full .

Anesthesia plays important role in the part of painkilling.Micro controller based anesthesia injector ppt covers explanation of block diagram, circuit diagram, introduction to project, software and hardware requirement .

MICROCONTROLLER BASED ANESTHESIA INJECTOR - Download as Word Doc .doc), PDF File .pdf), Text File .txt) or read online. In our project “Microcontroller based anesthesia injector”, we developed an automatic anesthesia injector implementing embedded system technology.

This micro controller based anesthesia injector provides the better solution in eliminating the problems caused due to the manual anesthesia injection. Download Microcontroller Based Anesthesia Injector Documentation Future scope: The current project is enhanced into a specialized embedded system which makes the operation simple, with reduced cost and increasing flexibility.

Automatic Anesthesia Injector system is also an application of embedded technologies in which a microcontroller is used to control the entire device. MICROCONTROLLER A Microcontroller is a general-purpose device that is meant to read data, perform limited calculations on that data and control its environment based on those calculations.

It can be defined as “Automatic administration of anesthesia based on the bio-medical parameters of the patient. Therefore it is necessary to arrest the pain and the blood loss..

indicators should be lit or dark and motors can be either turned on or off and so forth.

Microcontroller Based Anesthesia Injector Electronics Project Report